How To Measure Fingers For Rings
Loosely wrap the finger you want to put on the ring locate and mark where the ends meet. Start by cutting out a strip of paper that is approximately 34-inch wide and 4 inches long.
You can measure your ring size using either string or perhaps a more common item in your home floss.
How to measure fingers for rings. Use a pen to mark the point on the stringpaper where it overlaps forming a complete circle. The one that best matches is your ring size. Take one of these measurement tools and wrap it around the base of your finger marking where the string or floss first overlaps with a pen.
Even if you bring in a thumb ring we can usually come up with a close approximation of what size their ring finger will be. The number closest to the pen mark is the ring size in inches. Wrap it around the base of the appropriate finger.
Step 3 - Mark the point on the stringpaper where it overlaps forming a circle. Use the chart to determine your ring size. Fingers get bigger in warm weather and shrink in cold weather.
With a pen carefully mark the spot where the string overlaps with its end and either hold it up to a ruler that has millimeter measurements or to the graphic below. Featured Quality Assurance Benchmarks. You must wrap it around the finger you plan to wear your ring on otherwise the size will be inaccurate.
Wrap the piece of paper around the knuckle of your finger until it fits snugly. Use the pen to mark the string where it ends. Pull the pointed end Tab B through Slot A until the sizer is very snug.
Write down this measurement in millimeters and use the conversion chart above to find your ring size. The following are important tips to consider when measuring ring size. Wrap the intended finger snugly with a piece of stringfloss or strip of paper.
Take a piece of string ribbon thread or a thin strip of paper and wrap it around your finger close to the knuckle. Find a piece of string or strip of paper no wider than 12. If the base of your finger is a lot smaller than your finger knuckle is and youre using the virtual ruler measure both the base of your finger and your knuckle and select a size in between the two.
How To Measure Your Finger. Line the string up with the ring size guide provided on the ring size chart. Or do you need to figure out your own finger s.
The inside of the ring must be perfectly round for this to work. Step 1 - Get a non-stretchy string or paper about 6 152MM long and 14 65MM wide. With the numbers facing out wrap the sizer around the finger on where the ring will be worn.
Just use a millimeter ruler to measure the strip of paper. Wrap a piece of string around your ring finger and cut it at the point where the end overlaps. Measure your knuckle the same way following the previous steps.
Step 2 - Wrap around the base of your finger. Dont wrap it around where your ring will actually sit since your ring will need to be wide enough to fit over your knuckle. Finger size changes often as a result of the temperature.
Measure Your Finger One of the easiest ways to assess your ring size is to measure your finger with a strip of paper or string. Lay the string on the ruler with the area marked on your right. Wrap the string around the base of the ring finger slightly below the knuckle.
Use a pen to mark where the stringflosspaper meets around your finger Straighten out the stringflosspaper and measure it against a ruler in millimetres Check the chart in the Finger Circumference mm to find the ring size. Make sure that you grab a ring that your partner wears on a similarly sized finger the ring finger of their right hand being the optimal choice. Alternatively if you already own a great-fitting ring the process is even easier.
The larger of the two numbers aligned with Slot B is your ring size. Another way to measure a ring is to take a measurement of the inside and determine the finger size from a standard chart. Ring Size Measuring Tips.
If the measure lands between two. You can get your size by comparing your ring to a circular sizing chart. Wrap the paper around the base of the intended finger and then mark where the paper overlaps.
Then line that up with a ruler and take down its length in millimeters. Are you planning a proposal or special gift and need to know your partners finger size without them knowing. If you get 54 cm the size is 54 mm.
Please follow the directions below to measure your finger and to find out your ring size. It has to fit snug but not too tight. If the ring is in between two sizes choose the larger ring size.
How to measure ring size to help you find the size of a ring please use 5mm wide or simpler 1 cm tailoring paper. Measure your finger with a flexible measuring tape and convert the measurement using a ring size chart or ruler.
